DISCLAIMER: ANY SALE OF PRODUCTS OR DELIVERY OF CUSTOMER SUPPORT AND ADVICE BY HENKEL CORPORATION. AND/OR ITS AFFILIATES (“HENKEL”) IS MADE EXCLUSIVELY UNDER HENKEL’S STANDARD CONDITIONS OF SALE which are included in the applicable sales agreements, printed on the back of acknowledgments and invoices, or available upon request. HENKEL MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OF ITS PRODUCTS IN ANY CUSTOMER’S APPLICATION. Each customer should determine the suitability of Henkel’s materials for the customer’s particular use through appropriate testing and analysis. Statements regarding possible or suggested use of any material, product, service or design is not intended, nor should be construed, to grant any license under or induce infringement of any patent or other intellectual property. See product packaging for complete performance and warranty information.
The use of the “®” symbol designates registered or unregistered trademarks of Henkel Corporation or its affiliated companies
GE is a registered trademark of General Electric Company and is used under trademark license by Henkel.
†Estimates of comparative U.S. sales based on analysis of available 2018 industry reports and retail sales data.
1Fully cured sealant is resistant to stain-causing mold and mildew. Regular cleaning of sealant is required, however, as soap and other residue may cause secondary mold and mildew growth.
2Exposure to water possible in as little as 12 hours with bead size max 3/16″, temperature min 65°F and humidity min 50%. Do not touch or clean sealant for 24 hours.
3Based on comparison with products that meet the flexibility performance of ASTM C-920 Class 25 test requirements.
4Based on comparison of this sealant and GE Silicone 1* sealant using ASTM C794 Peel Adhesion test.
5Exposure to water possible in as little as 30 minutes with bead size max 3/16″”, temperature min 65°F and humidity min 50%. Otherwise, sealant should not be exposed to water for 8 hours. Do not touch or clean sealant for 24 hours.
6Sealant can be painted in as little as 30 minutes with bead size 3/16″”, temperature min 65°F & humidity min 50%. Otherwise, seals should not be painted for 2 hours. Spray paint can be applied immediately. Apply paint with reduced applicator pressure to avoid disturbing the caulk. Not recommended with oil-based paints. If oil-based paints are used, first test by applying an acrylic primer and paint in a small, inconspicuous area.
7Sealant can be painted in as little as 60 minutes with bead size max 3/16″, temperature min 65°F & humidity min 50%. Otherwise, sealant should not be painted for 2 hours or exposed to water for 8 hours. Do not touch for 24 hours, unless applying paint. Apply paint with reduced applicator pressure to avoid disturbing the sealant. Compatible with most latex and oil-based paints.
8Use backer rod for gaps deeper than 1/2″.
9Based on ASTM C-920, TYPE-S, NS, CLASS 25, analysis, product can span gaps of up to 2″ wide and 1/2″ deep with over 600% stretch and 25% joint movement.
10Sealant can be painted in as little as 45 minutes with bead size max 3/16″, temperature min 65°F & humidity min 50%. Otherwise, sealant should not be painted for 3 hours or exposed to water for 24 hours. Do not touch for 24 hours, unless applying paint. Apply paint with reduced applicator pressure to avoid disturbing the sealant. Clean up with a damp disposable cloth, do not rinse.
11Based on comparison of publicly available manufacturers’ specifications, product meets or exceeds the flexibility performance of any ASTM C-920, Class 35 or lower commercial Window & Door siliconized acrylic sealant.
12Based on ASTM C-920, TYPE-S, NS, CLASS 35 analysis, product can span gaps of up to 3″ wide and 1/2″ deep with over 800% stretch and 35% joint movement.
©2024 Henkel Corporation. All Rights Reserved.
