Product Finder: Pathway 1
Insulate a Home -> No to Insulate around a Window
GE Multipurpose Foam
- Seals small indoor & outdoor cracks up to 1”
- Withstands harsh UV rays for long-lasting results
- Offers high density for durability & overall insulation
- Withstands building & material movement
- Bonds to wood, concrete, brick, & more
- Tack-free in 8 minutes
GE Multipurpose Foam offers premium durability with flexibility, strong adhesion and UV resistance. Use to seal out air, moisture and pests in basements or crawl spaces, along with plumbing, HVAC or electrical penetrations and window & door projects.
- Always wear eye protection, gloves, and proper work clothing when using foam.
Cured foam is difficult to remove from skin, clothing and other substrates. - Sealant should be applied at temperatures between 41°F and 95°F. Can temperature
must be between 41°F and 86°F. - For optimum performance, shake can intermittently during extended use.
- Make sure the surface is clean and free from dirt, dust, and other substances. Cover
surfaces not intended to be foamed. - Invert can and dispense foam sparingly: Fill void by half to avoid overflows.
- Mist with water to speed cure.
- If necessary, cured foam can be trimmed with a knife after 1 hour.
- Clean spills immediately with acetone.
For products produced by Henkel Corporation, please use the UPC Code. You can click on the corresponding UPC code below to access the SDS..
| Color | UPC Code |
|---|---|
| White | 028756955337 |
Reviews
Gaps & Cracks
- Seals small gaps & cracks up to 1 inch
- Repels water & helps prevent mold & rot
- Blocks rodents & insects
- High R-5 insulating value
- Lifetime guarantee†
†See Product Disclaimers page for important details
Seal small gaps and cracks up to 1 inch with GE-branded Gaps and Cracks insulating foam, offering a water-resistant and airtight seal to keep out water and reduce drafts.
- Wear safety goggles, gloves, respiratory protection, and protective clothing. Protect surrounding areas with drop cloths.
- Shake can vigorously for one minute.
- Screw straw dispenser trigger completely onto can valve. Use caution to avoid activating the valve.
- To become familiar with product, test on experimental surface. Invert can and slowly depress the trigger to dispense the foam. Continue use in an inverted orientation.
- Fill rough openings approximately 1/3 full to allow for expansion. Release trigger 5 seconds before the end point, but keep straw end moving.
- For deep section application, allow the first layer of foam to cure before applying a second layer. Do not disturb uncured foam. See typical product information on label for times.
- Trim cured foam with a sharp knife or sand as needed. Foam exposed to sunlight must be painted or stained.
For products produced by Henkel Corporation, please use the UPC Code. You can click on the corresponding UPC code below to access the SDS..
| Color | UPC Code |
|---|---|
| White | 028756957379 |
Related Products
Reviews
Big Gaps & Cracks
- Expands & seals gaps greater than 1 inch
- Creates an airtight & water-resistant seal
- Helps save energy by reducing drafts
- High R-5 insulating value
- Lifetime guarantee†
†See Product Disclaimers page for important details
Fill gaps and cracks larger than 1 inch with GE-branded Large Gaps insulating foam, offering a water-resistant and airtight seal to keep out water and reduce drafts.
- Wear safety goggles, gloves, respiratory protection, and protective clothing. Protect surrounding areas with drop cloths.
- Shake can vigorously for one minute.
- Screw straw dispenser trigger completely onto can valve. Use caution to avoid activating the valve.
- To become familiar with product, test on experimental surface. Invert can and slowly depress the trigger to dispense the foam. Continue use in an inverted orientation.
- Fill rough openings approximately 1/3 full to allow for expansion. Release trigger 5 seconds before the end point, but keep straw end moving.
- For deep section application, allow the first layer of foam to cure before applying a second layer. Do not disturb uncured foam. See typical product information on label for times.
- Trim cured foam with a sharp knife or sand as needed. Foam exposed to sunlight must be painted or stained.
For products produced by Henkel Corporation, please use the UPC Code. You can click on the corresponding UPC code below to access the SDS..
| Color | UPC Code |
|---|---|
| White | 28756957362 |